A80L-0001-0081點監督型數字輸出模件，24VDC（#3624型）
色標 青綠色
輸出點數 16，共用的
推薦電壓范圍 16～30VDC
最大電壓 36VDC
邏輯功率 ＜10瓦
最大額定電流 0.7安/點；4.8安浪涌/10ms
最小要求負載 30mA
負載漏電流 最大4mA
保險（端子板） 不需要-輸出開關具有過電壓,過電流,超溫自保護
狀態指示燈
ON或OFF態 每點1個
模件狀態 PASS，F(xiàn)AULT，ACTIVE
現負載報警 POWER，LOAD（每點1個）
點隔離 最小1500VDC
OFF狀態時的短路檢測阻值 ＜5Ω
輸出診斷故障履蓋率
最大輸出觸發率 每100ms加上一次掃描
最小輸出觸發率 不要求
故障診斷周期 最大2mS,一般為500uS
ON時電壓降
底板上 250mA時，＜1.0VDC，典型的
1A時，最大＜1.0VDC
帶外部端子板，10英尺電纜 250mA時，＜2.0VDC，典型的
1A時，最大＜2.5VDC
帶外部端子板，99英尺電纜 250mA時，＜2.5VDC，典型的
1A時，最大＜6.0VDC
反向感應電勢保護（反電勢） I/O模件上有反向二極管
1.對于非公共端子板，必須給每點供電，包括不用的點。
2.最大輸入觸發率可以使I/O診斷正常地運行，探測出所有正常地可測出的故障。最小觸發率給出一故障覆蓋率，可以覆蓋在模件的計算出的平均故障間隔時間，（MTBF）的百分之十以內的正常不可探測到的故障。
3. “OVD”不能禁止。
聯系人：小費
ＱＱ：2851759102
郵箱：2851759102@qq.com
傳真：0592-5580710
電話：0592-2350124
手機：18050025437
Moore right angle plate for #1 rotary table
Seneca Falls, RO A80L-0001-0081 Universal b relief grinder workhead
Mazak CNC front panel
Mazak CNC M/T controller P/N 1PM-200, IPM-200
Mazak CNC 03-81581-01 circuit board, Fanuc 6MB
Gauthier (Germany) small gear hobber, hob, pinion, #3
Hispano Suiza (Swiss) Tool & Cutter grinder, 9" x 45.5"
Thomson Neff Muli5 gearbox 2" ballscrew screwjack, new
Kollmorgan servo motor
Amtech Ultraweld, ultrasonic bl welder
9 1/4" diameter magnetic chuck, magnet, D1-3 adapter
9 " diameter magnetic chuck, magnet
Sunnen hone, honing, stones lot
EDM set up table, 10" x 6", fluid flush in center
Norgren rodless cylinder, M/46016/M/609.600, Lintra
York 025-38145-001 water flow sensor, new
Huge tool post grinder, (3) different length spindles
Westhoff precision EDM electrode drilling machine
Hurco Ultimax CNC front panel
Hurco Ultimax CNC master firmware tape drive
Dynapath System 10 CNC, includes extra boards
Airserco 8900 VG vacuum gauge
ACME 9 KVA 3-phase transber, 480 / 240 volt
Hardinge Sjogren 22J collet chuck, D1-6 mount, Lot #1
Hardinge Sjogren 22J collet chuck, D1-6 mount, Lot #2
Sinker EDM center finder, microscope, Charmilles
Noburmatic, Nobur, deburring tools, lot of (3)
Mitsubishi M25K C4G35 CNC sinker, ram EDM, 3Robomatic
Moore jig borer grinder vise, Lot #2
Mitts Merrill #2 Giant keyseater, broach
Moore jig grinder positive stop, Lot #3
M & M Tool Roto-Grind sine table attachment, 7" dia
Moore slot grinder head, electric, Lot #2
Moore 9,000 rpm low speed grinding spindle
Strausak (Swiss) small gear hobber, hob, pinion
Zagar vert/horiz collet holding fixtures with collets
Craley 6" diameter boring head, Morse #6, Lot #1
Craley 6" diameter boring head, Morse #6, Lot #2
Craley 6" diameter boring head, NMTB 50 taper, Lot #3
Craley 6" diameter boring head, Morse #5 taper, Lot #5
Dayton 1/2 h.p. 90 volt DC gear motor, 12.5:1 ratio, #1
Dayton 1/2 h.p. 90 volt DC gear motor, 12.5:1 ratio, #2
Cylindrical grinding wheels, 24" OD x 12"ID, lot of (8)
Moore 9,000 rpm low speed grinding spindle, #2
Moore 9,000 rpm low speed grinding spindle, #3
Moore 40,000 rpm jig grinding grinder spindle
Moore 60,000 rpm jig grinding grinder spindle, #1
Moore 60,000 rpm jig grinding grinder spindle, #2
Moore 60,000 rpm jig grinder head boot
Moore jig grinder head boots, A80L-0001-0081 aluminum rings, lot
Aptec air valves, SS, VCR fittings, large lot, unused
Moore jig grinder micro-sine table, 12.5" x 14", Lot #3
Sprecher + Schuh CA3-9 CT3-12,contactor, overload,relay
Banner Engineering MGCA-4A machine guard control box
Fanuc transber, A80L-0001-0081
Magnalock multi-angle sine plate, 6" x 6"
Blanchard grinding wheel segments, lot #1
Blanchard grinding wheel segments, lot #2
Magnacraft solid state relay
Greco CNC Mini File
