下載PDF版完整參數(shù)表:
| 產(chǎn)品闡述 | ||
|---|---|---|
|
KE1 switch cabinet module 4 bs and 4 outputs |
||
| General specifications | ||
|---|---|---|
| Slave type | A/B slave | |
| AS-Interface specification | V3.0 | |
| Required master specification | ≥ V3.0 | |
| UL File Number | E87056 | |
| Functional safety related beters | ||
| MTTFd | 90 a | |
| Mission Time (TM) | 20 a | |
| Diagnostic Coverage (DC) | 0 % | |
| Indicators/operating means | ||
| LED FAULT |
error display; LED red red: communication error or address is 0 red flashing: overload of outputs |
|
| LED PWR | AS-Interface voltage; LED green | |
| LED AUX |
ext. auxiliary voltage UAUX; dual LED green/red green: voltage OK red: reverse voltage |
|
| LED IN | switching state (b); 4 LED yellow | |
| LED OUT | Switching state (output); 4 LED yellow | |
| Electrical specifications | ||
| Auxiliary voltage (output) | 20 ... 30 V DC PELV | |
| Rated operating voltage | 26.5 ... 31.6 V from AS-Interface | |
| Rated operating current | ≤ 40 mA | |
| Protection class | III | |
| Surge protection | UAUX, Uin: Over voltage category III, safe isolated power supplies (PELV) | |
| Input | ||
| Number/Type | 4 bs for 2-wire sensors (PNP), DC or for mechanical contacts | |
| Supply | from external auxiliary voltage UAUX | |
| Input current | ≤ 8 mA (limited internally) | |
| Switching point | according to DIN EN 61131-2 (Type 2) | |
| 0 (unattenuated) | ≤ 2 mA | |
| 1 (attenuated) | ≥ 4 mA | |
| Signal delay | < 2 ms (b/AS-Interface) | |
| Signal frequency | ≤ 250 Hz | |
| Output | ||
| Number/Type | 4 electronic outputs, PNP, overload and short-circuit proof | |
| Supply | from external auxiliary voltage UAUX | |
| Current | 0.5 A per output , 2 A per module | |
| Voltage | ≥ (UAUX - 0.5 V) | |
| Usage category | DC-13 | |
| Compliance with standards and directives | ||
| Directive conbity | ||
| EMC Directive 2004/108/EC | EN 50295:1999 | |
| Standard conbity | ||
| Noise immunity | EN 61326-1:2006 | |
| Emitted interference | EN 55011:2009 | |
| Input | EN 61131-2:2007 | |
| Degree of protection | EN 60529:2000 | |
| Fieldbus standard | EN 50295:1999, IEC 62026-2:2006 | |
| Programming instructions | ||
| Profile | S-7.A.7 | |
| IO code | 7 | |
| ID code | A | |
| ID1 code | 7 | |
| ID2 code | 7 | |
| Data bits (function via AS-Interface) | b output | |
| D0 | IN1 O1 | |
| D1 | IN2 O2 | |
| D2 | IN3 O3 | |
| D3 | IN4 O4 | |
| Parameter bits (programmable via AS-i) | function | |
| P0 |
Communication monitoring P0 = 0 monitoring = off, the outputs maintain the status if communication fails P0 = 1 monitoring = on, i.e. if communication fails, the outputs are deenergised (default settings) |
|
| P1 |
Input filter P1 = 0 b filter on, pulse suppression ≤ 2 ms P1 = 1 b filter off (default settings) |
|
| P2 |
Synchronous mode P2 = 0 synchronous mode on P2 = 1 synchronous mode off (default settings) |
|
| P3 | not used | |
| Ambient conditions | ||
| Ambient temperature | -25 ... 60 °C (-13 ... 140 °F) | |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) | |
| Relative humidity | 90 % , noncondensing | |
| Pollution degree | 2 | |
| Mechanical specifications | ||
| Degree of protection | IP20 | |
| Connection |
removable spring double terminals rated connection capacity: rigid/flexible (with and without wire-end ferrules): 0.25 mm2 ... 1.5 mm2 recommended tools for 1.5 mm2: PxC CRIMPFOX ZA3 or Weidmüller PZ 6 roto |
|
| Material | ||
| Housing | PA 66-FR | |
| Mass | 80 g | |
| Mounting | DIN mounting rail | |
