渦殼式混流泵A雄縣渦殼式混流泵200HW-4
（3）配套功率它是指水泵應選配的動力機的功率，因此又稱用功率。常用符號為N配，它比軸功率大。這是因?yàn)閯?dòng)力機把動力傳遞給水泵的過程中，有傳動損失；同時還要考慮水泵工作時，流量及揚程有波動而可能出現動力機，因此動力機需有比水泵軸功率大的功率儲備。配套功率可按下式求得：動力安全系數×（千克/秒）×揚程（米）配套功率（千瓦）=—————————————————————102×水泵效率×傳動效率動力安全系數（或稱備用系數）可根據水泵軸功率大小確定，軸功率小時取大值。傳動交率要根據傳動類型和傳動方式確定。采用聯軸器直接傳動時，取0.99。采用皮帶傳動時，開口式傳動取0.98，交叉?zhèn)鲃?dòng)取0.9，半交叉?zhèn)鲃?dòng)取0.92～0.94；
*技術參數
(2)改變轉速的方法：改變皮帶輪外徑或改變齒輪減速器傳動比，也可選用不同轉速的動力機。jdhuiquan717
(3)水泵轉速改變后，其流量(Q)、揚程(H)和功率(N)的變化關系如下式所示： Q1=Q*n1/n H1=H*(n1/n)2 N1=N*(n1/n)3
式中：Q1、H1、N．分別代表轉速改變后的流量、揚程和功率。 Q、H、N分別代表規定轉速下的流量、揚程和功率。
(4)水泵轉速提高后，耗用功率增加，吸上真空度降低，壽命縮短。過分提高轉速會發生其它事故，故應慎用。
(5)水泵轉速過分降低時，泵的使用效益低，為此，應盡量避免泵在過低轉速下運行。用戶應按性能曲線圖選擇使用。
渦殼式混流泵A雄縣渦殼式混流泵200HW-4
（1）QJ型性能范圍流量2～500米3/時，揚程14～336米，配套功率0.55～160千瓦，適用井徑100～400毫米，共8種，有83個YQS型潛水異步電動機的規格，組成QJ型潛水電泵系列共338個系列型號。（2）使用條件電源為50赫茲、380伏的三相交流電源；水溫不超過20°C；井水含砂量9重量比）不超過0.01%；井水酸堿PH值為6.5～8.5；電機和泵應全部浸入水中運行。（3）結構特點水泵位于電泵上端，為離心式或混流式，采用水潤滑軸承，與電機軸用聯軸器剛性聯接。上端設有逆止閥體，以泵停機時倒流引起的超速反轉。電機位于電泵下端，為密封式充水濕式結構。定子繞組采用耐水的聚乙烯絕緣的尼龍護套多層結構電磁線。
2、允許吸上真空度[Hs]與必需汽蝕余量[NPSH]r的換算關系：
[Hs]≈10-[HPSH]c
[NPSH]r≈[NPSH]C+0.3
式中：[Hs]-允許吸上真空度 米
[NPSH]C-臨界汽蝕余量 米
[NPSH]r-必需汽蝕余量 米
*特征描述
HW 型蝸殼式混流泵是按國家標準最新系列而設計的高節能產品。其性能指標均達到國際先進水平，省材節能效果顯著。延伸搜索：水環真空泵
（一）用途
HW型混流泵為臥式、單級、單吸、懸臂蝸殼式混流泵，適用于農田排灌、工業、城鎮給排水及船塢、碼頭引水等。延伸搜索：水環真空泵
（二）特點
體積小、重量輕、流量大、效率高，汽蝕性能好，高效區范圍寬廣而平坦，結構簡單，使用管理方法，維修容易。延伸搜索：水環真空泵
（三）型號說明
以250HW—8為例：
250—泵進（出）水口直徑為250毫米。
8—泵總揚長為8米。
（四）水泵的傳動方式
我廠生產的HW型系列混流泵均機（電）兩用，其轉動方式視各地區動力情況而定，訂貨時根據原動機的型號（功率、轉速）確定水泵的傳動方式，以定皮帶輪的大小或聯軸器的規格。延伸搜索：水環真空泵
（五）水泵轉向：
從水泵進水口看葉輪為逆時針?lè)较蛐D(zhuǎn)（即箭頭所示的方向旋轉）。
渦殼式混流泵A雄縣渦殼式混流泵200HW-4
The materials for the Water Guide pipe, the pump body and the pump cover are cast iron. There are infiltrating grooves on the inner surface of the rubber guide bearing near the wheel, and the guide bearing is mounted directly in the housing of the pump body, which can be replaced on site after wear. The rolling bearings contained in the pump cover are two single-row phase ball bearings. The main factory producing guanting is Fujian Youxi guanting factory. (Ix) Manual pumping of labor-driven piston pumps, diaphragm pumps and screw pumps and other water extrb tools, collectively referred to as manual pumps. Manual pumps are divided into shallow well dynamic pumps and deep wells manual pumps. The flow rate of shallow well piston pump is 0.34~4.214 cubic meter/time, adapt to the suction process 2~7 meters. The flow rate of the deep well piston pump is 0.056~0.601 cubic meters/When the head is 15~40 m. The flow rate of the diaphragm pump is 0.8~6.01 cubic meters/when the flow rate of the screw pump is 0.056~0.671 cubic meter/time. (10) The pump shell of the pump is generally cast iron, it is easy to crack under the b of mechanical force or thermal stress.
Instructions for use (i) the HW mixed-flow pump is composed of main parts such as pump body, pump cover, impeller, pump shaft and bearing body. (Ii) The pump cover is a part of the pump connected to the inlet pipe, with a specified axial end gap between the end surface and the impeller (maintaining the specified axial bance after eliminating the axial activity gap of the bearing). The gap is too small to produce friction, too large will lead to the pump pressure water reflux, so that the pump efficiency is reduced, through the increase or decrease adjustment paper pad to meet the required requirements of the gap. Extended search: Water ring Vacuum Pump (iii) The sealing device is composed of a filler letter, a water seal letter, a filler cover and a lead powder (or oil immersion) asbestos root. Its role is: 1, in the tea to prevent air inhalation pump, play a sealing role. 2. When pumping, prevent water from flowing out of the pump too much along the shaft. (Iv) Shaft application to protect the shaft does not make it directly friction with the filler, if long-term use found that the bushing wear too much, can change the bushing. (V) The two supports of the pump shaft are bearings in the bearing body, and the bearing has an appropriate amount of grease in its body to lubricate the bearings. (Vi) The baffle on the shaft prevents water from flowing into the bearing body along the pump, thus protecting the bearing and extending its service life.
用途/應用領域
混流泵混流泵是一種比轉速較高的泵型,廣泛應用于農田灌溉,防澇排洪,污水處理,電站冷卻系統等領域.在大流量,低揚程的應用場合下,軸流泵揚程,流量變化范圍小,高效區窄,抗汽蝕性能差,使用混流泵代替軸流泵,能夠在發揮軸流泵優點的基礎上補償這些缺點,從而取得更好的使用效果.
高比轉速混流泵的設計方法
軸面流動計算
采用流線迭代法求解軸面流動.流線迭代法基于沿任意準正交線的軸面速度梯度方程和流體運動的連續方程,根據各子流道流量相等的原則,迭代求解沿準正交線的軸面速度梯度方程即可得到軸面流網.通過流線迭代法,在確定軸面流道輪廓之后,可以通過所需時間很短的迭代計算過程得到精確的軸面流網.圖1是流網所對應的軸面速度沿軸面流線的分布圖.
清水泵，管道泵等產品，首要效力范疇：冶金，礦山，造紙，石油，化工，發電，污水處理等工作的需求，熱銷。公司本著“質量第一，用戶是上帝，誠信守約”的效力主旨。污水泵高壓給水泵以高效的機制為客戶供給優秀的效力。深受用戶好評。公司現有鑄造才能單件單重達35噸。原料有：耐磨鋼，不銹鋼，雙項不銹鋼，鋁合金，哈氏合金，巴氏合金等耐磨，耐腐蝕資料。吸取了很多的國外先進技術。前進了咱們的工藝水平。產品質量安穩牢靠彌補了很多技術缺點具有加工才能，長度達18m，加工直徑6m等鏜，數控設備。首要產品有：渣漿泵，標準化工泵。全面精確，耐心詳盡，全方位，全過程。實：作業重實干，講實績，務實效，兢兢業業，腳踏實地。不搞?？欤好艚莘错憽?
