、軸承是套在泵軸上支撐泵軸的構件，有滾動軸承和滑動軸承兩種。滾動軸承使用牛油作為潤滑劑加油要適當一般為2/3～3/4的體積太多會發熱，太少又有響聲并發熱！滑動軸承使用的是透明油作潤滑劑的,加油到油位線。太多油要沿泵軸滲出并且漂賤，太少軸承又要過熱燒壞造成事故！在水泵運行過程中軸承的溫度至高在85度一般運行在60度左右，如果高了就要查找原因（是否有雜質，油質是否發黑，是否進水）并及時處理！
5、密封環又稱減漏環。葉輪進口與泵殼間的間隙過大會造成泵內高壓區的水經此間隙流向低壓區，影響泵的出水量，效率降低！間隙過小會造成葉輪與泵殼摩擦產生磨損。為了增加回流阻力減少內漏，延緩葉輪和泵殼的所使用壽命，在泵殼內緣和葉輪外援結合處裝有密封環，密封的間隙保持在0.25～1.10mm之間為宜。
6、填料函主要由填料，水封環，填料筒，填料壓蓋，水封管組成。填料函的作用主要是為了封閉泵殼與泵軸之間的空隙，不讓泵內的水流不流到外面來也不讓外面的空氣進入到泵內。始終保持水泵內的真空！當泵軸與填料摩擦產生熱量就要靠水封管住水到水封圈內使填料冷卻！保持水泵的正常運行。所以在水泵的運行巡回檢查過程中對填料函的檢查是特別要
| 型號 | 流量Q | 揚程 | 效率 | 電機功率 | 轉速 | 必需汽蝕余量 | 重量 | |
| H | η | P | n | (NPAH)r | ||||
| (m3/h) | (L/s) | (m) | (%) | (KW) | (r/min) | (m) | (kg) | |
| 80-100 | 35 | 9.72 | 13.8 | 67 | 3 | 2900 | 3 | 65 |
| 50 | 13.9 | 12.5 | 73 | |||||
| 65 | 18.1 | 10 | 70 | |||||
| 80-100A | 31.3 | 8.7 | 11 | 66 | 2.2 | 2900 | 3 | 55 |
| 44.7 | 12.4 | 10 | 72 | |||||
| 58 | 16.1 | 8 | 69 | |||||
| 80-125 | 35 | 9.72 | 22 | 67 | 5.5 | 2900 | 3 | 100 |
| 50 | 13.9 | 20 | 72.5 | |||||
| 65 | 18.1 | 17 | 70 | |||||
| 80-125A | 31.3 | 8.7 | 17.5 | 66 | 4 | 2900 | 3 | 80 |
| 45 | 12.5 | 16 | 71 | |||||
| 58 | 16.1 | 13.6 | 69 | |||||
| 80-160 | 35 | 9.72 | 35 | 63 | 7.5 | 2900 | 3 | 107 |
| 50 | 13.9 | 32 | 71 | |||||
| 65 | 18.1 | 28 | 70 | |||||
| 80-160A | 32.7 | 9.1 | 30.6 | 62 | 7.5 | 2900 | 3 | 106 |
| 46.7 | 13.9 | 28 | 70 | |||||
| 61 | 16.9 | 24 | 69 | |||||
| 80-160B | 30.3 | 8.4 | 26 | 61 | 5.5 | 2900 | 3 | 99 |
| 43.3 | 12 | 24 | 69 | |||||
| 56.33 | 15.6 | 21 | 68 | |||||
| 80-200 | 35 | 9.72 | 53.5 | 55 | 15 | 2900 | 3 | 177 |
| 50 | 13.9 | 50 | 69 | |||||
| 65 | 18.1 | 46 | 67 | |||||
| 80-200A | 32.8 | 9.1 | 47 | 54 | 11 | 2900 | 3 | 166 |
| 47 | 13.1 | 44 | 67 | |||||
| 61 | 16.9 | 40 | 66 | |||||
| 80-200B | 30.5 | 8.5 | 40.6 | 53 | 7.5 | 2900 | 3 | 116 |
| 43.5 | 12.1 | 38 | 65 | |||||
| 56.6 | 15.7 | 33.4 | 64 | |||||
| 80-250 | 35 | 9.72 | 83 | 52 | 22 | 2900 | 3 | 245 |
| 50 | 13.9 | 80 | 62 | |||||
| 65 | 18.1 | 72 | 59 | |||||
| 80-250A | 32.5 | 9 | 73 | 51 | 18.5 | 2900 | 3 | 215 |
| 46.7 | 13 | 70 | 60 | |||||
| 61 | 16.9 | 63 | 58 | |||||
| 80-250B | 30 | 8.3 | 62 | 50 | 15 | 2900 | 3 | 187 |
| 43.3 | 12 | 60 | 58 | |||||
| 56 | 15.6 | 54 | 57 | |||||
| 80-315 | 35 | 9.72 | 128 | 44 | 37 | 2900 | 3 | 360 |
| 50 | 13.9 | 125 | 54 | |||||
| 65 | 18.1 | 122 | 57 | |||||
| 80-315A | 32.5 | 9 | 112 | 43 | 30 | 2900 | 3 | 342 |
| 46.5 | 12.9 | 110 | 54 | |||||
| 60.5 | 16.8 | 107 | 57 | |||||
| 80-315B | 31 | 8.6 | 102 | 42 | 30 | 2900 | 3 | 342 |
| 44.5 | 12.4 | 100 | 53 | |||||
| 58 | 16.1 | 98 | 56 | |||||
| 80-315C | 29 | 8.1 | 87 | 41 | 22 | 2900 | 3 | 277 |
| 41 | 11.4 | 85 | 51 | |||||
| 53.6 | 14.9 | 83 | 54 | |||||
| 80-350 | 35 | 9.72 | 156 | 53 | 55 | 2900 | 3 | 557 |
| 50 | 13.9 | 150 | 54 | |||||
| 60 | 16.7 | 14 | 52 | |||||
| 80-350A | 30.8 | 8.56 | 148 | 45 | 45 | 2900 | 3 | 441 |
| 44 | 12.2 | 142 | 51 | |||||
| 52.8 | 14.7 | 135 | 50 | |||||
| 80-350B | 28 | 7.78 | 142 | 39 | 37 | 2900 | 3 | 378 |
| 40 | 11.1 | 135 | 48 | |||||
| 46 | 12.8 | 128 | 46 | |||||
| 80-100(I) | 70 | 19.4 | 14 | 66 | 5.5 | 2900 | 4.5 | 110 |
| 100 | 27.8 | 12.5 | 76 | |||||
| 130 | 36.1 | 11 | 75 | |||||
| 80-100(I)A | 62.6 | 17.4 | 12 | 64 | 4 | 2900 | 4.5 | 88 |
| 89 | 24.7 | 10 | 74 | |||||
| 116 | 32.2 | 8.8 | 74 | |||||
| 80-125(I) | 70 | 19.4 | 23.5 | 70 | 11 | 2900 | 4.5 | 164 |
| 100 | 27.8 | 20 | 76 | |||||
| 130 | 36.1 | 14 | 72 | |||||
| 80-125(I)A | 62.6 | 17.4 | 19 | 68 | 7.5 | 2900 | 4.5 | 114 |
| 89 | 24.7 | 16 | 74 | |||||
| 116 | 32.2 | 11 | 65 | |||||
| 80-160(I) | 70 | 19.4 | 36.5 | 70 | 15 | 2900 | 4.5 | 187 |
| 100 | 27.8 | 32 | 76 | |||||
| 130 | 36.1 | 24 | 75 | |||||
| 80-160(I)A | 65.4 | 18.2 | 32, | 68 | 11 | 2900 | 4.5 | 175 |
| 93.5 | 26 | 28 | 74 | |||||
| 121 | 33.8 | 21 | 67 | |||||
| 80-160(I)B | 60.6 | 16.8 | 27 | 66 | 11 | 2900 | 4.5 | 175 |
| 86.6 | 24.1 | 24 | 72 | |||||
| 112 | 31.3 | 18 | 65 | |||||
| 80-200(I) | 70 | 19.4 | 54 | 65 | 22 | 2900 | 4 | 253 |
| 100 | 27.8 | 50 | 74 | |||||
| 130 | 36.1 | 42 | 73 | |||||
| 80-200(I)A | 65.4 | 18.2 | 47.5 | 64 | 18.5 | 2900 | 4 | 221 |
| 93.5 | 26 | 44 | 73 | |||||
| 121 | 33.8 | 37 | 72 | |||||
| 80-200(I)B | 61 | 16.9 | 41 | 62 | 15 | 2900 | 4 | 200 |
| 87 | 24.2 | 38 | 71 | |||||
| 113 | 31.4 | 32 | 70 | |||||
| 80-250(I) | 70 | 19.4 | 87 | 62 | 37 | 2900 | 4 | 333 |
| 100 | 27.8 | 80 | 71 | |||||
| 130 | 36.1 | 68 | 78 | |||||
| 80-250(I)A | 65.4 | 18.2 | 76 | 61 | 30 | 2900 | 4 | 315 |
| 93.5 | 20.6 | 70 | 68 | |||||
| 121 | 33.8 | 59.5 | 67 | |||||
| 80-250(I)B | 61 | 16.9 | 65 | 60 | 30 | 2900 | 4 | 271 |
| 87 | 24.2 | 60 | 66 | |||||
| 113 | 31.4 | 51 | 66 | |||||
| 80-315(I) | 70 | 19.4 | 132 | 55 | 75 | 2900 | 4 | 680 |
| 100 | 27.8 | 125 | 67 | |||||
| 130 | 36.1 | 114 | 66 | |||||
| 80-315(I)A | 66.5 | 18.5 | 119 | 59 | 55 | 2900 | 4 | 537 |
| 95 | 26.4 | 113 | 65 | |||||
| 123 | 34.3 | 103 | 64 | |||||
| 80-315(I)B | 63 | 17.5 | 106 | 58 | 45 | 2900 | 4 | 425 |
| 90 | 25 | 101 | 65 | |||||
| 117 | 32.5 | 92 | 63 | |||||
| 80-315(I)C | 58 | 16.1 | 90 | 56 | 37 | 2900 | 4 | 370 |
| 82 | 22.8 | 85 | 63 | |||||
| 107 | 29.7 | 76 | 61 | |||||
