1、了解所需切割的材料，如有必要可以通過降低空氣壓力來降低鋸片的轉動速度。 2、確保牢固固定了所需切割的材料，防止其移動。 3、氣動空氣馬達時，用手指按壓閥桿，然后開始切割。 4、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命。（注意：避開切割后可能掉落的碎片。切割即將完成時，切勿使鋸碰到您的身體、工件或附近的其它人員。） 5、關閉空氣馬達時，釋放閥桿。 6、下次切割開始前，鋸片必須保持運動狀態。氣動鋸時，鋸片不能接觸任何表面。 7、斷開空氣軟管時，關閉空氣軟管閥。斷開前，先打開空氣閥給軟管減壓。 8、更換鋸片前，務必?cái)嚅_(kāi)空氣軟管，并推動閥桿以釋放掉馬達內的壓力。 9、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開
用氣量：0.6P3 最大切割直徑: 圓管（150mm）方管（150*220mm） 轉速 ：160-230/min 機器尺寸:680*200*230 mm 外箱尺寸:75*25*25 cm 鋸條尺寸:13*0.65*1332 mm 凈重:6kg 毛重:8kg 建議壓氣管：Φ12mm 一、適用場所 1.氣動鋸無需擔心火花帶來的危險，所以適用于煤礦及化工等危險環境作業，廣泛用于切割大直徑管道、槽鋼、鋼絲線纜等金屬，非金屬切割。 2.無火花切割，可在高溫下、潮濕環境中作業無漏電危險。 3.氣動**鋸，結構緊湊，牢固可靠、重量輕便 攜帶方便，一人僅可操作，降低工人的勞動強度，提高工作效率。 二、產品配置 1.主機一套 2.鋸條1根 3.合格證一份 4.使用說明書一份 本公司嚴格按照ISO900國際質量體系制定了《質量控制手冊》及《售后服務控制程序》，并嚴格按合同要求及產品技術規范為用戶提供相關服務，我們一直以高質量的產品和一流的服務贏得客戶的信賴，深受廣大客戶的歡迎與支持。公司不僅有技術精湛、經驗豐富的售后隊伍，還緊跟E代潮流，實施互聯網銷售、**作業服務，為客戶提供更高效的售后服務。
1, understand the material needed to cut, if necessary to reduce the speed of rotation of the saw blade by reducing the pressure of the air. 2, ensure that the required cutting material is firmly fixed to prevent its movement. 3. When pneumatic air motor is operated, the stem is pressed with the finger, and then the cutting is started. 4, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life. (notice: avoid debris that may fall after cutting. When the cutting is about to be finished, do not make the saw touch your body, the workpiece, or the other people in the vicinity. 5. When the air motor is closed, the stem is released. 6. The saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw. 7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose. 8. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane. 9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.
