設備主要特點Main features of equipment
一、油浴式電加熱噴體：
1、噴體溫度均勻，溫度穩定，溫度波動保證在≤0.1℃以內（解決了由于加熱溫度不均勻造成的丸子大小頭、假合縫等問題）。
2、由于溫度精度高可以降低膠片厚度0.1mm左右（節省明膠約10%左右）。
二、計算機自動調整注藥裝量
1、自動調整裝量，節約時間，節省原料。
2、裝量精度高，裝量精度為≤±1%，大大降低原料的損耗。
三、換向板、上下本體、左右墊條硬度達到HRC60-65.經久耐用：適合用戶生產各種液體混懸中藥品種，大大的提高了使用壽命。
四、模具鎖盤（三點鎖定）：鎖定后不跑線，同時兼有微調功能，操作非常簡單。
五、微量潤滑系統：油量根據轉速自動調節。（降低石蠟油耗，節約成本）
六、內置冷風系統，配備冷水機。
七、膠皮滾采用單獨變頻調速：生產時如果膠液質量不好可通過膠皮滾調速來解決。
八、出丸區冷風定型設計；避免拉網軸纏網膠，使膠囊成型更美觀 。
九、模具下丸部分采用特殊的斜斗，清洗非常方便。
十、供料泵與機頭采用外側傳動，供料泵內的潤滑油不會進入機頭。（供料泵獨立密封）
1. Oil bath electric heating spray body:
1. The temperature of the spray body is unib, the temperature is stable, and the temperature fluctuation is guaranteed to be within ≤ 0.1 ℃ (solved the problems of the ball head and false joint caused by uneven heating temperature)
2. Due to the high temperature accuracy, the film thickness can be reduced by about 0.1mm (saving about 10% of gelatin).
Second, the computer automatically adjusts the injection volume
1. Automatically adjust the loading volume, save time and save raw materials.
2. The loading accuracy is high, and the loading accuracy is ≤ ± 1%, which greatly reduces the loss of raw materials.
3. The hardness of the reversing plate, upper and lower bodies, left and right pads reaches HRC60-65. Durable: suitable for users to produce various liquid suspension Chinese medicine varieties, greatly improving the service life.
Fourth, the mold lock disk (three-point locking): does not run the line after locking, and also has a fine-tuning function, the operation is very simple.
5. Trace lubrication system: The oil quantity is automatically adjusted according to the speed. (Reduce paraffin oil consumption and save costs)
6. Built-in cold air system, equipped with chiller.
7. The rubber roller adopts a separate frequency conversion speed regulation: if the quality of the glue is not good during production, it can be solved by the rubber roller speed regulation.
8. Cold air setting design in the pill-out area; avoid entanglement of the mesh with the mesh and make the capsule more beautiful.
Nine, the lower part of the mold uses a special inclined bucket, which is very convenient to clean.
10. The feed pump and the machine head are driven outside, and the lubricating oil in the feed pump will not enter the machine head. (The feed pump is independently sealed)
技術參數：Technical Parameters:
|
型號Model |
RJN-65 |
RJN-100 |
RJN-250 |
|
滾模額定轉速Rolling mould rated speed |
0-5r/min |
0-5r/min |
0-5r/min |
|
滾模尺寸Rolling die size |
Φ64×65mm |
Φ64×100mm |
Φ150×250mm |
|
單柱塞供給量Single plunger supply |
4x(0-2ml) |
6x(0-1.5ml) |
20x(0-1.5ml |
|
裝量精度 Loading accuracy |
±1% |
±1.5% |
±2% |
|
產量Yield（0.5g） |
8900粒/小時 |
15600粒/小時 |
76000粒/小時 |
|
電壓Voltage |
AC220V50HZ |
AC220V50HZ |
AC380V50HZ |
|
總功率Total power |
3.6kW |
4.2KW |
12KW |
|
主機外形尺寸Host size |
1400x700x1660mm |
1400x700x1660mm |
1980x850x1860mm |
|
65型 輔 機 （標 配） 65 type auxiliary machine (standard) |
|||
|
定型轉籠 Stereotype cage |
轉籠尺寸：φ320x450mm 轉速：21轉/分鐘 Rotating cage size: φ320x450mm speed: 21 rpm |
||
|
化膠罐 Plastic tank |
容積：30L 帶保溫、攪拌及儀表電器控制 Volume: 30L with insulation, mixing and instrument electrical control |
||
|
不銹鋼膠體磨Stainless steel colloid mill |
細度：20-70微米 轉速：3200轉/分 Fineness: 20-70 microns Speed: 3200 rpm |
||
|
冷水機 Chiller |
制冷溫度：-5～16度 Refrigeration temperature: -5 ~ 16 degrees |
||
|
晾干盤 Drying tray |
托盤尺寸：720x520x50mm 數量：20個 Tray size: 720x520x50mm Quantity: 20 |
||
